Mill for All Seasons HLF project - the story so far

The latest news at the Mill is that we have a new HLF project called "A Mill for All Seasons". The project runs until June 2018 and will involve fitting new millstones and renovating parts of the mill mechanism so that we can mill using motor power as well as wind power. We'll be using this blog to keep you up to date with what we're doing; future posts  will be in more detail, but to start us off here is a quick report on progress so far!  

June 2017

·         Local groups contacted about outreach, school visits and community exhibition

·         Advertising in place for new volunteers

July 2017

·         Outreach sessions: Carers group, Scouts and Beavers, Swavesey WI

·         Press release sent out and interview with Radio Cambridgeshire

August 2017

·         Carers’ drop in session at the museum

        Day centre outreach talk

·         Windmill box created for use in handling talks and with special school pupils

September 2017

·         Mill workshop for volunteers

·         Visit from Burwell Early Learners

·         Talks for public at Fen Edge Harvest Fair event

·         Top millstone removed in preparation for being replaced

October 2017

·         Burwell brownies outreach and craft session

·         CPD session with teachers from Burwell Village College

·         U3A group visit

November 2017

·         Tractor refurbished and ready to run

·         Engage outreach group at library

·         Colourbox nursery visit

·         Burwell village college visit

·         Millwright dressing bedstone

·         Sensory box session with Castle School

Update - 10 February 2015

After some of the strong winds last month one of the striking gears, the gear which controls whether the shutters are open or closed, was bent and the shutters were forced closed. 

Abseiling off the top of the mill, reattaching the striking gear after being bent back.

A brave member of the team abseiled up the sails to release the striking gear and gently lower it to the ground. Once on the ground they used the contraption pictured below to bend the gear back into shape, it was then raised back up and reattached to the sail.

The device used to bend the striking back into shape

Update - 8 January 2015

The new girders shown on the last update were successfully fitted by the mill team. The new girders have stopped the distortion that used to occur as the cap turned in the wind.

The new girders installed in the cap either side of the brake wheel

Four guide wheels have been fitted in the cap, two at the rear and two on the sides, which keep the cap centred on top of the tower. They've fixed one of the major problems we had which was when the wind pushed on the cap, it caused it to slide backwards and disengaged the gearing that kept it facing the wind. However, for the past three weeks the mill has been rotating on its own to face the wind, and has been through some strong winds without any problems.

The two guide wheels at the back of the cap

Close up on one of the guide wheels

The waterproofing was completed just before the weather turned and apart from a very small leak in the cap, has also been successful.

The next job for the mill team will be to prepare the mill stones in order to start milling flour.

Update - 9 August 2014

It's been a while since we updated this Blog so here's what's been going on recently....

Since the sails were put on, the cap hasn't always been turning freely so it's been hard for the fantail to point the sails into the wind. To help the cap run more smoothly we have installed two skate bearings which greatly reduce the friction round the track below the cap.

Skate bearing

The cap was also distorting slightly when it turned, so we are aiming to stiffen it with metal girders. The girders were welded by Burwell firm N & G Marsh, and will be fitted in the next few weeks. They are very heavy and it will be quite a challenge for the Mill Team to lift them into place - they'll be hoisted through the trap doors used for taking sacks of grain to the top floor. That's the easy bit! Once the girders are on the top floor they will need to be installed in the cap. Easier said than done, but the Mill Team are confident they can meet the challenge.

Girders in the museum workshop in the process of being painted. You can get an idea of the size of the girders by comparing them to our ride-on lawn mower at the far end of the workshop.

 Waterproofing work on the cap is currently taking place (as you may have seen on the museum's Facebook page). This has involved hanging from the cap in a harness. Since the photo was taken a ladder has been purchased, which has been specially bent to the same curvature of the cap. It is hung from the finial and the person working on the waterproofing stands on the ladder but still wears a safety harness. This makes working much easier as tools can be hung on the ladder rungs. It is also more comfortable as the person's weight is not being taken by the harness the whole time! 

Waterproofing the cap

Grand Reopening of Stevens Mill

On Sunday 13th April Burwell Museum Trust reopens its windmill, Stevens' Mill, to the public following a year-long restoration.
The museum site will be open to the public from 12 noon - 4pm. Free Admission!
The reopening ceremony of the windmill starts at 12.30pm - Sir James Paice MP will officially open the windmill at 12.45pm.
This will be a great day out for all ages - bread making demonstrations, a cake decorating competition (see poster below for competition info), a working forge, tours of the windmill, make your own windmill out of junk and much more including a Time Capsule put together by local school children being hidden in the windmill.

This form can be downloaded from our website. 
They will also be available from the museum on the day.

www.burwellmuseum.org.uk